PUTHON Responder One Guide d'installation

Responder OneRemote Start Installation GuideNOTE:This product is intended for installation by a profes-sional installer only! Any attempt to install t

10© 2008 Directed Electronics. All rights reserved.Virtual tachVirtual Tach is a new feature for Directed this year. It is the default RPM-sensing m

11© 2008 Directed Electronics. All rights reserved.Component locations and finding wiresFor detailed information on where to locate components, and how

12© 2008 Directed Electronics. All rights reserved. Primary harness (H1) wiring diagramH1/1LIGHT GREEN/BLACKFACTORY ALARM DISARMH1/2GREEN/WHITE FACTO

13© 2008 Directed Electronics. All rights reserved. Door lock harness, 3-pin connector1BLUE (-) UNLOCK OUTPUT2EMPTY NOT USED3GREEN (-) LOCK OUTPUT* *

14© 2008 Directed Electronics. All rights reserved.Primary harness (H1), 9-pin connectorH1/1LIGHT GREEN/BLACKFACTORY ALARM DISARMThis wire sends a neg

15© 2008 Directed Electronics. All rights reserved.Relay for Positive (+) Disarm WireH1/2GREEN/WHITE FACTORY REARMThis wire sends a negative pulse eve

16© 2008 Directed Electronics. All rights reserved.H1/4WHITE/BLUE (-) ACTIVATION INPUT This input comes from the factory set to 1 activation pulse. Th

17© 2008 Directed Electronics. All rights reserved.H1/6BROWN (-) HORN OUTPUTThis wire supplies a (-) 200 mA output that can be used to honk the vehicl

18© 2008 Directed Electronics. All rights reserved.Note: this feature is not available with the 1 button remote.H1/8BLACK (-) chassis GROUND connectio

19© 2008 Directed Electronics. All rights reserved.Note: For parking light systems that draw 10 amps or more, the jumper must be placed to the (-) lig

Bitwriters with a date code of 6a or older require an IC upgrade (p/n 998M). Some Bitwriters with a date code of 6B do not require the IC upgrade, ref

20© 2008 Directed Electronics. All rights reserved.Heavy gauge relay interfaceThe heavy gauge wires are used to energize high current circuits in the

21© 2008 Directed Electronics. All rights reserved.5PINK/WHITE (+) PROGRAMMABLE OUTPUT FOR ACCESSORY OR IGNITIONConnect this wire to the second igniti

22© 2008 Directed Electronics. All rights reserved.Figure A Figure BImportant! Always use the Vehicle Safety Check section of this guide to verify tha

23© 2008 Directed Electronics. All rights reserved.H2/3BROWN (+) BRAKE SWITCH SHUTDOWN WIREThis wire MUST be connected to the vehicle’s brake light wi

24© 2008 Directed Electronics. All rights reserved.Neutral safety switch interfaceSome vehicles do not have an electrical neutral safety switch. Inste

25© 2008 Directed Electronics. All rights reserved.eral Motors product or a Dodge Dakota pickup, please call Directed Electronics Technical Support fo

26© 2008 Directed Electronics. All rights reserved.Programming jumpersLight flash (+)/(-)This jumper is used to determine the light flash output polar

27© 2008 Directed Electronics. All rights reserved.Plug-in program switchThe Program switch plugs into the blue two-pin connector.Tach learning Virtu

28© 2008 Directed Electronics. All rights reserved. To learn the tach signalDRW-961. Start the vehicle with the key.2. Within 5 seconds, press and HO

29© 2008 Directed Electronics. All rights reserved.Remote control learn routineThe system comes with two transmitters that have been taught to the rec

ContentsGovernment Regulations ...5Warning! Safety first ...

30© 2008 Directed Electronics. All rights reserved.Ch Function3Reset Features: This resets features all of the security system to the factory default

31© 2008 Directed Electronics. All rights reserved.Learn Routine will be exited if:Ignition is turned off.sProgram switch is pressed too many times.s

32© 2008 Directed Electronics. All rights reserved.Operating settings learn routineThe System Features Learn Routine dictates how the unit operates. T

33© 2008 Directed Electronics. All rights reserved.Once the Program switch has been pressed and released the desired number of times, press it once mo

34© 2008 Directed Electronics. All rights reserved.Features menuThe factory default settings are indicated in boldTEXTINTHETABLEBE-low. Menu 1Fe

35© 2008 Directed Electronics. All rights reserved. Menu 2Fea-ture # Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+1 Engine checkingVirtual tachvoltage O

36© 2008 Directed Electronics. All rights reserved.Feature descriptionsThe features of the system are described below with default settings in bold.

37© 2008 Directed Electronics. All rights reserved.5 UNLOCK OUTPUT—1, 2 PULSES: This will program the unlock output to one or two pulses. When the dou

38© 2008 Directed Electronics. All rights reserved.(2) Comfort closure 1 - Activates the 20 second timer after the door lock pulse. (3) Comfort Closur

39© 2008 Directed Electronics. All rights reserved.and shuts down. Programmed to the default setting the engine will run for 12 minutes. If the 24 or

40© 2008 Directed Electronics. All rights reserved.to-start period of a diesel motor. When ON the accessory comes on when the wait-to-start output is

41© 2008 Directed Electronics. All rights reserved.¢ Bitwriter®The Bitwriter® has the ability to fine tune certain features of the security system.

42© 2008 Directed Electronics. All rights reserved.Shutdown diagnosticsThe unit has the ability to report the cause of the last shutdown of the remote

43© 2008 Directed Electronics. All rights reserved.LED FLASHES SHUTDOWN MODE1 System timed out2 Over-rev shutdown 3 Low or no RPM, Low batter

44© 2008 Directed Electronics. All rights reserved.Important: Make sure there is adequate clearance to the front and rear of the vehicle before attemp

45© 2008 Directed Electronics. All rights reserved.TroubleshootingThe starter cranks for six seconds but does not start.sEither the wrong ignition wi

46© 2008 Directed Electronics. All rights reserved.Does the vehicle have an immobilizer? Some immobilizer systems 4.will not allow the vehicle to cran

47© 2008 Directed Electronics. All rights reserved.The vehicle will start and run only for about 10 seconds.sIs the remote start programmed for volta

48© 2008 Directed Electronics. All rights reserved.Wiring quick reference guideBROWN (-) horn honk outputOff OnRED/WHITE (-) 200mA channel 2 output

49© 2008 Directed Electronics. All rights reserved.Wiring quick reference guide continuedORANGE (-) ground when locked (Not used)red 4 pin d2dbitwrite

5© 2008 Directed Electronics. All rights reserved.Government RegulationsThis device complies with Part 15 of FCC rules. Operation is subject to the fo

54© 2008 Directed Electronics. All rights reserved.N4203V 2008-09Vista, CA 92081www.directed.com© 2008 Directed Electronics—All rights reservedThe co

6© 2008 Directed Electronics. All rights reserved.Warning! Safety firstThe following safety warnings must be observed at all times:$UETOTHECOMPLEXIT

7© 2008 Directed Electronics. All rights reserved.TIONIMMEDIATELYANDCONSULTWITHTHEUSERTOlXTHEPROBLEMIMMEDIATELYAfter the remote start modu

8© 2008 Directed Electronics. All rights reserved.What is includedThe control module (see diagram)sResponder One transceiver (P/N 6212T)sTwo, 2-wa

9© 2008 Directed Electronics. All rights reserved.Installation points to rememberImportant: This product is designed for fuel-injected, automatic tran